DAVIS 6152 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 60

DAVIS 6152 Скачать руководство пользователя страница 58

54

Verifying Setup

To verify that you have successfully set up your console to receive a repeater in the
console’s Current Weather Mode:
1. View the transmitter information displaying at the bottom of the

console screen.

If the transmitter ID being repeated is displayed and an “X” flashes in the bottom
right corner of the ticker tape, the transmitter is being repeated and received by the
console successfully.
The repeater’s information also displays at the bottom of the console’s diagnostics
screens.

Clearing Repeater ID

If a repeater ID is being displayed in Screen 2 and you are not using a repeater with
the selected station, you must turn off the repeater function to receive station
information successfully.
In Setup Screen 2:
Press 2ND and then press WIND repeatedly so that the console cycles through the
list of repeater IDs (Repeaters A-H) until the section where the repeater ID was
displayed is blank. Press DONE to continue to the next screen or press and hold
DONE to return to the Current Weather Mode.

«
...
56
57
58
59
60
»

Содержание 6152





























































Отзывы:

Нет отзывов