Dave Smith Instruments Poly Evolver Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 72

Dave Smith Instruments Poly Evolver Скачать руководство пользователя страница 39

39

MIDI

The envelopes will be triggered by MIDI notes only.

MIDI rst

The envelopes will be triggered by MIDI, and the sequencer will
be reset on every note (if it is running). The sequencer will not
trigger the envelopes.

MID Gate

Gated mode – the envelopes will only be triggered when a MIDI
note is held and the sequencer is running; in other words the
MIDI notes will gate the sequencer.

AUTO

MIDI G r

Gated mode, reset – same as Gated mode, except every time a
MIDI note is hit, the sequencer is reset to step 1.

AUTO

Ext In

The envelopes are gated by the Left external audio input signal
level, in other words, when the signal gets above a fixed
threshold, the envelopes start. The envelopes then go into the
release phase when the signal level drops below a second fixed
threshold.

Ext In r

Same as external in, but also resets the sequencer to step 1.

Ext Gate

External In signal will gate the sequencer (sequencer must be
on).

AUTO

Ext G r

External In signal will gate the sequencer (sequencer must be
on). And also resets the sequencer to step 1 on each new gate.

AUTO

MS Once

Plays a sequence once (according to the length of Sequence 1)
when a new MIDI note is received. The sequence is not restarted
on multiple MIDI notes until it finishes and stops.

AUTO

MS Once R

Also plays a MIDI sequence once, but will re-start the sequence
on each MIDI note.

AUTO

EiSqStep

Plays one step of the sequencer on each External Input audio
trigger.

AUTO

MdSqStep

Plays one step of the sequencer on each MIDI note received.

AUTO

Transpose:

-36…+36

Transpose control for this Part; 0 is centered,

steps in semitones. Note that it is summed with the Global Transpose, and the overall
limit of the two controls is –36 to +36. For example, if the Combo is transposed down
two octaves (-24) and you then turn the Global transpose down two octaves, summing
the two would be –48, which is out of range. In this case, it automatically adds
octaves to keep it in range.

Fine Freq:

-50…+50

Fine Tune control for this Part; 0 centered,

steps in cents (50 cents = ½ semitone). As with the Transpose, it is summed with the
Global Fine Freq, and the summed limit is –50 to +50.

Volume:

0…100

Sets the Volume level for this Part.

Low Key:

C -2…C 8

This parameter, along with the High Key parameter

following, sets the keyboard range that this part will respond to. The frequency over a
10 octave range, from 8 Hz to 8KHz, stepping in semitones. C3 is middle C (MIDI
note 60). The keyboard range is used for setting up keyboard splits, for example when
Part 1 is set from C-2 to C2 with one voice (unison), and Part 2 is set from C#2 to C 8
with 3 voices (Poly 3).

«
...
37
38
39
40
41
...
»

Содержание Poly Evolver









































































Отзывы:

Нет отзывов