manualshive.com logo in svg

Datex-Ohmeda S/5 M-P, Техническое описание слота

Поделиться
Скачать
Datex-Ohmeda S/5 M-P Скачать руководство пользователя страница 30

Datex-Ohmeda S/5 monitors

Document No. 8001013-1

26

values do not indicate a failure, but the continuous counting (more than 50 per second) during the

normal operation indicates either serial communication failure or module not in place.

RAM 

indicates the state of the RAM memory. 

ROM 

indicates whether the checksum in the EPROM

is in accordance with the one the software has calculated. 

EEPROM

 indicates if the values stored

in the permanent memory are valid. The state is either 

OK, Fail

 or 

? 

(module not in place or a

communication error).

5.2

 

P/PT calibration menu

Protection

Protection for the configuration and temperature calibrations can be set ON and OFF only when
protect button at the bottom of the module is pressed.

Set Config

The module configuration should be set according to the module type. The setting is possible only
when the protection is set OFF. The available selections are BP or PT.
The configuration setting should be checked if the PT board is replaced.

Calibrate T3 and Calibrate T4

The functions are for calibrating the temperature channels T3 and T4. The calibrations are possible

only when the protection is set OFF. The temperature calibration requires accurate test plugs of

value 25 °C and 45 °C.
Calibration:
1.

 

Select Calibrate T3 / Calibrate T4

2.

 

Insert the test plug 25 °C into the T3 / T4 connector

3.

 

Press the ComWheel

4.

 

Insert the test plug 45 °C into the T3 / T4 connector

5.

 

Press the ComWheel

Calibrate P3

The function is for calibrating the invasive blood pressure channel P3.
The calibration requires a pressure transducer (with an appropriate cable) and a pressure

manometer.

Содержание S/5 M-P











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды