Datex-Ohmeda 7100 Скачать руководство пользователя страница 62

Страница: 62 / 158

7100 Anesthesia Ventilator

4-22

02/03 1006-0836-000

4.9.8

Service Calibrations

Required

The

Service Calibrations Required

menu displays which setting or

calibration must be performed when the “Service Calibration

” alarm

appears in normal operation. After the setting or calibration is properly
completed, the text for that setting or calibration will be removed.

Remarks

The normal operation “Service Calibration

” alarm message is only removed

when all the required settings or calibrations are completed.

The

Set

“

Service Calibration

” menu item is used by the factory to activate

the “Service Calibration

” alarm and require that all settings and calibrations

be performed when the machine is set up for operation at its permanent
location.

You can reset the “Service Calibration

” alarm in the field by selecting

“Yes” when the following warning appears after selecting the
“Set Service Calibration

” menu item.

Содержание 7100






























































































































































Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды

Datex-Ohmeda 7100, Техническое справочное руководство

Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды