Datex-Ohmeda 7100 Скачать руководство пользователя страница 48

Страница: 48 / 158

7100 Anesthesia Ventilator

4-8

02/03 1006-0836-000

4.7 User Settings

In normal operation, the user can set several parameters to a personal
preference or to compensate for the surrounding influences. The range of some
of these settings can vary from machine to machine.

The

User Settings

menu is used to adjust the range to normalized values.

4.7.1 Screen Contrast

The range from minimum to maximum screen contrast varies for individual
displays. The

Screen Contrast

menu is used to tailor the range so that the

screen image is still visible at minimum and maximum contrast settings for the
user.

Remarks

The “Minimum Screen Contrast” and the “Maximum Screen Contrast” settings
set the range of contrast values for the operator.

The “Optimal Screen Contrast” setting sets the default value.

Содержание 7100






























































































































































Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды

Datex-Ohmeda 7100, Техническое справочное руководство

Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды