manualshive.com logo in svg

Datex-Ohmeda 7100, Техническое справочное руководство

Поделиться
Скачать
Datex-Ohmeda 7100 Скачать руководство пользователя страница 31

2 Theory of Operation

1006-0836-000     02/03     

2-17

2.4.7 Serial interface

The serial board (SAB/SICB) provides two functions:

•

It serves as an interface between the control board and switches that 
are located in the machine itself (not in the breathing system).

•

 It processes serial communications signals from the control board 
to the RS232 connector (COM 1) on the back panel of the Aestiva 
machine.

Machine Switches

The machine switches include:

•

the System On/Standby switch

•

the O

2

 supply pressure switch

•

the O

2

 flush switch

Serial Communications

The serial interface provides isolated RS232 serial communications. The 
TXD (transmit) and RXD (receive) signals between the SAB and the control 
board are at RS232 levels. 

Circuits on the board change the signals to digital 5V levels; isolate them 
through optocouplers; then, change them back to RS232 levels before 
sending them to the outside world. 

•

The external communications signals conform to standard 
RS-232C signal standards. 

•

COM 1 is a 15-pin female D connector.

•

It’s configured for Data Communications Equipment (DCE)

•

Pin 6 - receive data

•

Pin 13 - transmit data

•

Pin 5 - signal ground

In addition to the above, the SICB in the Aespire machine provides remote 
monitor On/Off through an isolated relay.

•

Pin 1 - MON On/Standby

•

Pin 9 - MON On/Standby return

MACHINE SWITCHES

CONNECTOR

7100 CONTROL BOARD

CONNECTOR

RS232

ISOLATED

DRIVER /

RECEIVER

ISOLATION

TRANSFORMER

OPTICAL

ISOLATORS

7100 SERIAL POR

T

CONNECTOR

ISO_RXD1

ISO_TXD1

ISO_RXD

ISO_TXD

RXD1_232

TXD1_232

RXD_232

TXD_232

/O2_FLUSH

GND

LOW_O2_SW

GND

/O2_FLUSH

LOW_O2_SW

REM_ON

REM_ON

ISOLATED POWER

RS232

ISOLATED

DRIVER /

RECEIVER

AB.43.096

Note regarding SICB:

The machine switch signals 
come in on three separate 
connectors.

Содержание 7100































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды