Datex-Ohmeda 7100 Скачать руководство пользователя страница 100

Страница: 100 / 158

7100 Anesthesia Ventilator

5-20

02/03 1006-0836-000

5.4.6 No ventilation

troubleshooting

* Refer to Section 7.2,

“Breathing System Leak Tests,”

in the respective anesthesia machine Technical Reference Manual.

Yes

Start

Zero Flow and

airway pressure

transducers

Verify pass?

High flow Gas

exhausts from

drive gas port?

1. Remove bellows assembly

2. Enter Valves - Test Tool

3. Turn on the flow valve to 15 L/min

4. Check regulator calibration

Yes

Correct Hospital

Supply Problem

Perform airway pressure

transducer calibration or

proceed to Inaccurate

Ventilation Troubleshooting

Section 5.4.3

Yes

1. Turn off the flow valve

2. Turn on the PEEP Safety Valve

3. Set the PEEP valve to 100 cm H2O

4. Using hand, occlude bleed resistor

on bottom of vent engine

Gas exhausts from

PEEP control port?

Regulator

pressure OK

at 25 psi?

Set Flow valve

to 70 L/min

Check hospital

pressure supply

Hospital supply

pressure OK at

35-100 psi?

Replace Regulator

and perform all

valve calibrations

Yes

Inspiratory Flow Valve Problem

1. Check electrical connections

2. Attempt inspiratory flow valve

calibration

3. Replace inspiratory valve if

necessary and recalibrate

Setup for PEEP Valve

Calibration but use the

Valve test tool menu:

With Peep valve set to

100 cm H

Yes

Pressure

90-110 cm H

1. Examine Exhalation

Valve and exhalation

valve diaphragm and

reassemble breathing

circuit

2. Reduce PEEP setting

to 70 cm H

3. Place a plug in the

drive port of the

Bellows Assy. The

bellows can be left off

4. Occlude inspiratory

port and press flush

button

Yes

Does Circuit

Pressurize?

Does Bellows

Move?

Check all valve calibrations.

If OK, go to Breathing System

Leak Troubleshooting if bellows

does not refill

Proceed to Breathing

Circuit Leak

Troubleshooting

1. Close PEEP Safety Valve and

Remove PEEP Valve from the

Vent Manifold

2. Turn on PEEP Safety Valve

Does flow come from

vent engine plate?

PEEP Safety Valve Problem

1. Check electrical supply

and connections

2. Replace if necessary

PEEP Control Valve Problem

1. Check electrical supply

and connections

2. Attempt Recalibration

3. Replace if necessary

Yes

Check function of

the drive pressure

pop-off valve

Yes

Problem solved?

If not replace filter

Yes

AB.43.103

Содержание 7100






























































































































































Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды

Datex-Ohmeda 7100, Техническое справочное руководство

Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды