DATATEC HAMEG HM8135, Руководство пользователя

Страница: 26 / 64

26
General information concerning the CE marking
General information
concerning the
CE marking
General remarks regarding the CE marking
Hameg measuring instruments comply with the EMI
norms. Our tests for conformity are based upon the rele-
vant norms. Whenever different maximum limits are optio-
nal Hameg will select the most stringent ones. As regards
emissions class 1B limits for small business will be applied.
As regards susceptibility the limits for industrial environ-
ments will be applied.
All connecting cables will influence emissions as well as
susceptability considerably. The cables used will differ
substantially depending on the application. During practi-
cal operation the following guidelines should be absolutely
observed in order to minimize emi:
1 . Data connections
Measuring instruments may only be connected to external
associated equipment (printers, computers etc.) by using
well shielded cables. Unless shorter lengths are prescri-
bed a maximum length of 3 m must not be exceeded for
all data interconnections (input, output, signals, control). In
case an instrument interface would allow connecting seve-
ral cables only one may be connected.
In general, data connections should be made using dou-
ble-shielded cables. For IEEE-bus purposes the double
screened cable HZ72 from HAMEG is suitable.
2 . Signal connections
In general, all connections between a measuring instru-
ment and the device under test should be made as short
as possible. Unless a shorter length is prescribed a maxi-
mum length of 3 m must not be exceeded, also, such con-
nections must not leave the premises.
All signal connections must be shielded (e.g. coax such as
RG58/U). With signal generators double-shielded cables
are mandatory. It is especially important to establish good
ground connections.
3. External influences
In the vicinity of strong magnetic or/and electric fields even
a careful measuring set-up may not be sufficient to gu-
ard against the intrusion of undesired signals. This will not
cause destruction or malfunction of Hameg instruments,
however, small deviations from the guaranteed specifica-
tions may occur under such conditions.
HAMEG Instruments GmbH
KONFORMITÄTSERKLÄRUNG
DECLARATION OF CONFORMITY
DECLARATION DE CONFORMITE
Hersteller / Manufacturer / Fabricant / Fabricante:
HAMEG Instruments GmbH · Industriestraße 6 · D-63533 Mainhausen
Die HAMEG Instruments GmbH bescheinigt die Konformität für das Produkt
The HAMEG Instruments GmbH herewith declares conformity of the product
HAMEG Instruments GmbH déclare la conformite du produit
Bezeichnung: HF-Synthesizer
Product name: RF-Synthesizer
Designation: HF-Synthesizer
Typ / Type / Type: HM8135, HM8135X
mit / with / avec: HO820
Optionen / Options /
Options:
HO880
mit den folgenden Bestimmungen / with applicable regulations /
avec les directives suivantes:
EMV Richtlinie: 2004/108/EG
EMC Directive: 2004/108/EG
Directive CEM: 2004/108/EG
Niederspannungsrichtlinie: 2006/95/EG
Low-Voltage Equipment Directive: 2006/95/EG
Directive des equipements basse tension: 2006/95/EG
Angewendete harmonisierte Normen / Harmonized standards applied /
Normes harmonisées utilisées:
Sicherheit / Safety / Sécurité:
EN 61010-1 (07/2011)
Elektromagnetische Verträglichkeit / Electromagnetic compatibility /
Compatibilité électromagnétique:
EMV Störaussendung / EMI Radiation / Emission CEM:
EN 61326-1 (10/20116)
IEC/CISPR 11 ( 2009, modif A1:2010), DIN VDE 0876 (10/2007), DIN VDE 0877
(08/2007)
Störfestigkeit / Immunity / Imunitee:
EN 61326-1 (10/20116)1
EN 61000-4-2 (12/2009), EN 61000-4-3 (04/2011), EN 61000-4-4 (11/2010),
EN 61000-4-5 (06/2007), EN 61000-4-6 (12/2009), EN 61000-4-8 (11/2010),
EN 61000-4-11 (02/2005)
Datum / Date / Date
21. 06. 2012
Unterschrift / Signature / Signatur / Signatura
Holger Asmussen
General Manager