Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 27

Страница: 27 / 103

GENERAL INFORMATION ON DEVICE POSITIONING

PRODUCT REFERENCE GUIDE

Emitter and receiver orientation

The two units shall be assembled parallel each other, with the beams arranged at right

angles with the emission and receiving surface, and with the connectors pointing to the

same direction.
The configurations shown in the figure must be avoided:

Figure 14: Wrong light curtain TX-RX orientations

Use of deviating mirrors

The control of any dangerous area, with several but adjacent access sides, is possible

using only one safety device and well-positioned deviating mirrors.
The figure shows a possible solution to control two different access sides, using one mir

ror placed at 45° with respect to the beams.

Figure 15: Use of deviating mirrors

The operator must respect the following precautions when using the deviating mirrors:

• The alignment of the emitter and the receiver can be a very critical operation

when deviating mirrors are used. Even very small displacements of the mirror is

enough to lose alignment.

• The use of Datasensing laser pointer accessory is recommended under these con

ditions.

• The minimum safety distance (S) must be respected for each single section of the

beams.

• The effective operating range decreases by about 20% by using only one deviating

mirror.

The following table shows estimated operating distances relating to the number of mir

rors used.

• The presence of dust or dirt on the reflecting surface of the mirror causes a drastic

reduction in the range.

NO. OF MIRRORS

OPERATING DISTANCE (14mm)

OPERATING DISTANCE (30mm)

10 m

8 m

Mirror

DANGEROUS

AREA

Содержание SH4 BASE-STANDARD








































































































Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы:

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 27 / 103

Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы: