Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 25

Страница: 25 / 103

GENERAL INFORMATION ON DEVICE POSITIONING

PRODUCT REFERENCE GUIDE

Distance between homologous devices

The following graphic shows the distance from the interfering devices (Ddo) according

to the operating distance (Dop) of the couple (TXA – RXA).
If different safety devices have to be installed in adjacent areas, the emitter of one

device must not interfere dangerously with the receiver of the other device.
The TXB interfering device must be positioned outside a minimum Ddo distance from

the TXA – RXA emitter-receiver couple axis.

Figure 11: Distance between homologous devices

This minimum Ddo distance depends on:

• the operating distance between emitter (TXA) and receiver (RXA)
• the effective aperture angle of the ESPE (EAA)

Figure 12 - ESPE Type 4

The formula to get Ddo is the following:
Ddo (mm) = 263

for operating distance < 3 m

Ddo (m) = operating distance (m) x tg 5°

for operating distance ≥ 3 m

CAUTION: The interfering device (TBX) must be positioned at the same Ddo

distance, calculated as shown above, even if closer to TXA respect to RXA.

Installation precautions have to be taken to avoid interference between

homologous devices. A typical situation is represented by the installation

areas of several adjacent safety devices aligned one next to the other, for

example in plants with different machines.

0.2

Operating distance (D

)

s d

ist

ice

)

263

Содержание SH4 BASE-STANDARD








































































































Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы:

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 25 / 103

Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы: