Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 23

Страница: 23 / 103

GENERAL INFORMATION ON DEVICE POSITIONING

PRODUCT REFERENCE GUIDE

GENERAL INFORMATION ON DEVICE POSITIONING

The safety light curtain should be carefully positioned in order to provide the necessary

protection. Access to the dangerous area must only be possible by passing through the

protecting safety light beams.

Figure 5: Wrong light curtain positioning

Figure 6: Correct light curtain positioning

Under standard operating conditions, machine starting must not be possible while

operators are inside the dangerous area.
Where it is not possible to install safety light curtain very near to the dangerous zone, a

second light curtain must be mounted in a horizontal position in order to prevent any

lateral access, as shown in the following figures.

CAUTION: The figure below shows some examples of possible access to the

machine from the top and the bottom sides. These situations may be very

dangerous and so the installation of the safety curtain at sufficient height

in order to completely cover the access to the dangerous area (correct

positioning) becomes necessary.

CAUTION: If the operator is able to enter in the dangerous area, an addi

tional mechanical protection must be mounted to prevent the access.

Figure 7: Wrong light curtain

positioning

Figure 8: Correct light curtain

positioning

Содержание SH4 BASE-STANDARD








































































































Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы:

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 23 / 103

Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы: