manualshive.com logo in svg

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 22 / 103

Поделиться
Скачать
Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 22

INSTALLATION

14

   SH4 BASE-STANDARD

SAFETY INFORMATION

• The stopping system of the machine must be electrically controlled.
• This control system must be able to stop the dangerous movement of the machine 

within the total machine stopping time T as per paragraph "

Minimum installation 

distance" on page 10

 and during all working cycle phases.

• Mounting and connection of the safety light curtain must be carried out by quali

-

fied personnel only, according to the indications included in the special sections 

(refer to "

Installation" on page 6

, "

Mechanical Mounting" on page 22

, "

Connections" 

on page 26

, "

Alignment Procedure" on page 48

) and in the applicable standards.

• The safety light curtain must be securely placed in a particular position so that 

access to the dangerous zone is not possible without the interruption of the 

beams (refer to "

Installation" on page 6

).

• The personnel operating in the dangerous area must be well trained and must 

have adequate knowledge of all the operating procedures of the safety light cur

-

tain.

• The TEST button must be located outside the dangerous zone because the opera

-

tor must check the dangerous zone during all Test operations.

• The RESET/RESTART button must be located outside the dangerous zone because 

the operator must check the dangerous zone during Reset/Restart operations.

CAUTION: For a correct and safe use of the safety light curtains, the follow

-

ing points must be observed:

NOTE:  Please  carefully  read  the  instructions  for  the  correct  functioning

before powering the light curtain on.

Содержание SH4 BASE-STANDARD








































































































Отзывы:

Нет отзывов