Datalogic QuickScan QM24 series Скачать руководство пользователя страница 44

Страница: 44 / 314

Enter/Exit Programming Mode

QuickScan™ I QD24XX/QBT24XX/QM24XX

Beep On Not on File

This option enables/disables the action of the reader to sound a three beep sequence upon

receiving a Not-On-File (NOF) host command.

$CBPNF00(CR)

Beep On Not On File = Disable

DEFAULT

$CBPNF01(CR)

Beep On Not On File = Enable

ACK NAK Options

This enables/disables the ability of the reader to support the RS-232 ACK/NAK protocol.

See

page 234

for more information.

DEFAULT

$CR2AE00(CR)

ACK/NAK Protocol = Disable ACK/NAK

$CR2AE01(CR)

ACK/NAK Protocol = Enable for label transmission

$CR2AE02(CR)

ACK/NAK Protocol = Enable for host-command

acknowledge

$CR2AE03(CR)

ACK/NAK Protocol = Enable for label transmission and host-

command acknowledge

Содержание QuickScan QM24 series



























































































































































































































































































































Результаты поиска

Содержание QuickScan QM24 series

Отзывы:

Datalogic QuickScan QM24 series, Руководство по продукции, Страница: 44 / 314

Результаты поиска

Содержание QuickScan QM24 series

Отзывы: