Datalogic QuickScan Lite QW2400 Скачать руководство пользователя

Страница: 23 / 288

Customizing Configuration Settings

Product Reference Guide

Interface Settings

The scanner is typically factory-configured with a set of default features stan-

dard to the interface type you ordered. See

"Interface Selection"

on page 11.

Global Interface Features, starting on page 19

provides settings configurable by all

interface types. If your installation requires you to further customize your scan-

ner, you can select other options through use of the instructions and program-

ming bar codes available in the appropriate section for your interface.

•

RS-232 ONLY Interface, starting on page 21

•

RS-232/USB-COM Interfaces, starting on page 25

•

RS232 OPOS

•

USB Composite (COM + Keyboard)

•

Keyboard Interface, starting on page 35

•

USB-OEM Interface, starting on page 67

Configuring Other Features

If your installation requires different programming than the standard factory

default settings, the following sections of this manual allow configuration of

non-interface-specific settings you might require:

Configuration Using Bar Codes

General Features includes programming for scan-

ning, speaker and LED indicators and other such universal settings.

Reading Parameters

Reading Parameters include programming for scanning,

speaker and LED indicators and other universal settings.

1D Symbologies

Includes options concerning the bar code label types (symbolo-

gies). These settings allow you to enable/disable symbologies, set label

lengths, require check digit, etc.

Software Version Transmission

The software version of the device can be transmitted over the RS-232, Key-

board and USB interfaces by scanning the following label.

Transmit Software Version

RevA

Содержание QuickScan Lite QW2400

































































































































































































































































































Результаты поиска

Содержание QuickScan Lite QW2400

Отзывы:

Похожие инструкции для QuickScan Lite QW2400

Бренды по названию

Популярные бренды

Datalogic QuickScan Lite QW2400, Руководство по продукции

Результаты поиска

Содержание QuickScan Lite QW2400

Отзывы:

Похожие инструкции для QuickScan Lite QW2400

Бренды по названию

Популярные бренды