Datalogic PowerScan PD9530 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 362

background image

Introduction

6

PowerScan™ PD9530/PBT9500/PM9500

charge / charge cycles before needing replacement. This number is higher if

partial discharging / recharging is adhered to rather than full / deep dis-

charging,
The typical manufacturer advertised useful life of LI batteries is one to three

years, depending on usage and number of charges, etc., after which they

should be removed from service, especially in mission critical applications.

Do not continue to use a battery that is showing excessive loss of capacity, it

should be properly recycled / disposed of and replaced. For most applica-

tions, batteries should be replaced after one year of service to maintain cus-

tomer satisfaction and minimize safety concerns.
Collect and recycle waste batteries separately from the device in compliance

with European Directive 2006/66/EC, 2011/65/EU, 2002/96/EC and 2012/

19/EU and subsequent modifications, US and China regulatory and others

laws and regulations about the environment.

Programming the Reader

Configuration Methods

Programming Bar Codes

The reader is factory-configured with a standard set of default features.

After scanning the interface bar code, you can select other options and cus-

tomize your reader through use of the instructions and programming bar

code labels available in the corresponding features section for your inter-

face. Customizable settings for many features are found in

starting on page 21.

Some programming labels, like

"Restore Custom Defaults"

require only the scan of the single label to enact the change. Most, however,

require the reader to be placed in Programming Mode prior to scanning

them. Scan an ENTER/EXIT bar code once to enter Programming Mode. Once

the reader is in Programming Mode, scan a number of parameter settings

before scanning the ENTER/EXIT bar code a second time, which will then

accept your changes, exit Programming Mode and return the reader to nor-

mal operation.

There are some exceptions to the typical programming sequence
described above. Please read the description and setting instructions
carefully when configuring each programmable feature.

Datalogic Aladdin™

Datalogic Aladdin™ is a multi-platform utility program providing a quick and

user-friendly configuration method via the RS-232/USB-COM interface.

Aladdin allows you to program the reader by selecting configuration com-

mands through a user-friendly graphical interface running on a PC. These

commands are sent to the reader over the selected communication interface,

or they can be printed as bar codes to be scanned. Aladdin also facilitates

image capturing.
In addition, Aladdin makes it easy to upgrade the handheld’s firmware, to

attain the benefits of new reader features. Reference the Datalogic Aladdin™

Online Help for more details.
Aladdin is available for download free of charge on the Datalogic website.

«
...
14
15
16
17
18
...
»

Содержание PowerScan PD9530











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerScan PD9530

Бренд: Cidron Страницы: 27

Бренд: Intermec Страницы: 16

FlashMover MS-Direct

Бренд: Microdia Страницы: 5

Бренд: Opticon Страницы: 8

Бренд: I-Rocks Страницы: 4

Бренд: Velleman Страницы: 19

Бренд: MSI Страницы: 1

Бренд: Iseo Страницы: 2

Бренд: Atid Страницы: 49

CHIPDRIVE micro 100

Бренд: TOWITOKO Страницы: 8

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 8

B-FP802-CR-QM-S

Бренд: Toshiba Страницы: 16

Бренд: Toshiba Страницы: 38

Бренд: Toshiba Страницы: 43

Бренд: Toshiba Страницы: 37

Бренд: Toshiba Страницы: 46

B-EP2DL-GH40-QM-R

Бренд: Toshiba Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды