Enter/Exit Programming Mode
Product Reference Guide
265
SET FUNCTION KEY LABELS
Set F1 Label
This item allows the user to change the default mnemonic label associated
to each individual function key. This is done by programming a short acro-
nym 4-character string to be shown in the bottom of the display. The pur-
pose of the label is to serve as an indication of the programmed function of
the Function Key below it.
$CPWSB
Set F1 label
To configure this feature, scan the ENTER/EXIT PRO-
GRAMMING MODE bar code above, then the bar code at
left followed by 8 digits from the
. The digits must be the hexadecimal ASCII repre-
sentation of the desired characters.
End by scanning the ENTER/EXIT bar code again.
Set F2 Label
This item allows the user to change the default mnemonic label associated
to each individual function key. This is done by programming a short acro-
nym 4-character string to be shown in the bottom of the display. The pur-
pose of the label is to serve as an indication of the programmed function of
the Function Key below it.
$CPWSC
Set F2 label
To configure this feature, scan the ENTER/EXIT PRO-
GRAMMING MODE bar code above, then the bar code at
left followed by 8 digits from the
. The digits must be the hexadecimal ASCII repre-
sentation of the desired characters.
End by scanning the ENTER/EXIT bar code again.
Set F3 Label
This item allows the user to change the default mnemonic label associated
to each individual function key. This is done by programming a short acro-
nym 4-character string to be shown in the bottom of the display. The pur-
pose of the label is to serve as an indication of the programmed function of
the Function Key below it.
$CPWSD
Set F3 label
To configure this feature, scan the ENTER/EXIT PRO-
GRAMMING MODE bar code above, then the bar code at
left followed by 8 digits from the
. The digits must be the hexadecimal ASCII repre-
sentation of the desired characters.
End by scanning the ENTER/EXIT bar code again.
Set F4 Label
This item allows the user to change the default mnemonic label associated
to each individual function key. This is done by programming a short acro-
nym 4-character string to be shown in the bottom of the display. The pur-
pose of the label is to serve as an indication of the programmed function of
the Function Key below it.
$CPWSE
Set F4 label
To configure this feature, scan the ENTER/EXIT PRO-
GRAMMING MODE bar code above, then the bar code at
left followed by 8 digits from the
. The digits must be the hexadecimal ASCII repre-
sentation of the desired characters.
End by scanning the ENTER/EXIT bar code again.
Содержание PowerScan 950X Series
