Datalogic MX-U81 Скачать руководство пользователя страница 29

Страница: 29 / 66

MX-U81 Hardware Guide

U1xx Camera Dimensions

3-3

Datalogic S.r.l.

U1xx Camera Dimensions

This section provides dimensions for the U1xx series of cameras.

Mounting the Camera

This section provides instructions for mounting the U1xx camera and dimensions for the camera mounting block.

To mount a U1xx camera

1. With the mounting block held tightly against the camera body, insert the mounting bolts through the block mount-

ing bolt holes (see diagram).

Mounting Block (95A903029) and Camera Body

Bottom View

(also see “U1xx Mounting Block (95A903029)” on page 3-4)

UNITS: inch [mm.]

Power/Trigger
Connection

USB
Connection

0.22 [5.5]

Rear View

(without mounting block)

1.14 [29]

1.0 [25]

0.74[18.7]

Block Mounting holes

3 x M3

Fasteners provided

2 x 1/4-20; 0.31 [8] deep

1.14 [29]

2 x M2; 0.16 [4] deep

0.71 [18]

0.30 [7.6]

0.47 [12]

1.15 [29.3]

1.63 [41.3]

Side View

(without mounting block)

2 x M5

0.31 [8] deep

0.5 [12]

1.14 [29]

0.25 [6.3]

Содержание MX-U81



































































Результаты поиска

Содержание MX-U81

Отзывы:

Похожие инструкции для MX-U81

Бренды по названию

Популярные бренды

Datalogic MX-U81, Руководство по оборудованию

Результаты поиска

Содержание MX-U81

Отзывы:

Похожие инструкции для MX-U81

Бренды по названию

Популярные бренды