manualshive.com logo in svg

Datalogic DSM0400, Руководство по продукции

Datalogic DSM0400 - бесплатное скачивание быстрого справочного руководства пользователя для вашего удобства. Получите доступ к основным функциям и настройкам с помощью этого полезного руководства. Скачайте его с manualshive.com прямо сейчас, чтобы быть в курсе всех возможностей этого устройства.

Поделиться
Скачать
background image

Customizing Configuration Settings

Product Reference Guide

13

Interface Settings

The scanner is typically factory-configured with a set of default features stan-

dard to the interface type you ordered. See 

Using the DSM0400 on page 9

. 

Configuration Using Bar Codes

 provides settings configurable by all interface 

types. If your installation requires you to further customize your scanner, you 

can select other options through use of the instructions and programming bar 

codes available in the appropriate section for your interface.

•

RS-232 ONLY Interface, starting on page 17

•

USB Keyboard ONLY Interface, starting on page 23

•

USB-OEM ONLY Interface, starting on page 51

Configuring Other Features

If your installation requires different programming than the standard factory 

default settings, the following sections of this manual allow configuration of 

non-interface-specific settings you might require:

Configuration Using Bar Codes

: 

General Features includes programming for scan-

ning, speaker and LED indicators and other such universal settings.

Reading Parameters

: 

Reading Parameters include programming for scanning, 

speaker and LED indicators and other universal settings.

2D Symbologies

: 

Includes options concerning the bar code label types (symbolo-

gies). These settings allow you to enable/disable symbologies, set label 

lengths, require check digit, etc.

Software Version Transmission

The software version of the device can be transmitted over the RS-232, Key-

board and USB interfaces by scanning the following label.

Transmit Software Version

Resetting the Product Configuration to Defaults

If you aren't sure what programming options are in your scanner, or you've 

changed some options and want to restore the Default Configuration, scan the 

Restore Default Configuration

 bar code below. This will restore the factory config-

uration for the currently active interface.

NOTE

Defaults are based on the interface type. Configure the scanner for the 
correct interface before scanning this label.

Содержание DSM0400





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSM0400

xpr RTT User Manual preview
RTT
Бренд: xpr Страницы: 10
LAUNCH TECH OBD BOOK 6830 Manual preview
OBD BOOK 6830
Бренд: LAUNCH TECH Страницы: 31
RIOTEC iLS6302ABU Programming Quick Manual preview
iLS6302ABU
Бренд: RIOTEC Страницы: 4
Bosch R90 Installation Manual preview
R90
Бренд: Bosch Страницы: 2
TSYS RP350x User Manual preview
RP350x
Бренд: TSYS Страницы: 83
Siemens AR20M-MF User Manual preview
AR20M-MF
Бренд: Siemens Страницы: 34
Unitech MS840P User Manual preview
MS840P
Бренд: Unitech Страницы: 8
Zebex Z-8082 Lite User Manual preview
Z-8082 Lite
Бренд: Zebex Страницы: 22
Inner Range 994720 Installation Manual preview
994720
Бренд: Inner Range Страницы: 2
Ocom OCBS-W700 Setting Manual preview
OCBS-W700
Бренд: Ocom Страницы: 27
GE Interlogix 840 Installation Manual preview
840
Бренд: GE Interlogix Страницы: 34
GE Interlogix 260 Installation Manual preview
260
Бренд: GE Interlogix Страницы: 36
Corzus CR 704 User Manual preview
CR 704
Бренд: Corzus Страницы: 3
mt-mobility MT 1890 Operation Manual preview
MT 1890
Бренд: mt-mobility Страницы: 3
IDTECK IPK101 Quick Installation Manual preview
IPK101
Бренд: IDTECK Страницы: 8
IDTECK PROX10 User Manual preview
PROX10
Бренд: IDTECK Страницы: 13
IDTECK SR10B User Manual preview
SR10B
Бренд: IDTECK Страницы: 16
IDTECK SR10RW User Manual preview
SR10RW
Бренд: IDTECK Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды