Datalogic AREX 401 Скачать руководство пользователя страница 88

Страница: 88 / 148

AREX™ 401

CHAPTER 7

ACCESSORIES

The accessories listed here below are described for information purposes only, and are

not necessarily included in the packaging. The minimum contents of the packaging
include the main hardware, cables and keys. For additional information, please see
“Contents of the packaging” on page 10.

CONTROL BOX

This accessory is used to control the laser marker through the Control Box interface.

The Control Box allows to perform the following functions:

•

Changing laser marker state

•

Starting and Stopping the marking process

•

Showing the marking process state

•

Showing the system error state

Figure 64: Control Box (ordering no: 985330031)

NOTE: See “X1 - Command Box (Laser Control)” on page 33 for detailed
control signal description.

Содержание AREX 401





















































































































































Результаты поиска

Содержание AREX 401

Отзывы:

Похожие инструкции для AREX 401

Бренды по названию

Популярные бренды

Datalogic AREX 401, Руководство пользователя

Результаты поиска

Содержание AREX 401

Отзывы:

Похожие инструкции для AREX 401

Бренды по названию

Популярные бренды