Datalogic AREX 401 Скачать руководство пользователя страница 77

Страница: 77 / 148

SYSTEM PROTECTION

USER MANUAL

•

Wait for system reboot

•

Check if the Tray-bar icon color is

GREEN

(protection enabled)

Disable the system protection

•

Open the System Protection tool GUI

•

Click the

DISABLE

button

•

A message advise the User to confirm the new setting. Press

YES

to disable System

Protection

•

A message advise the User that the system will be rebooted. Press

YES

to continue

CAUTION: DO NOT turn OFF or UNPLUG the system while Windows® is shut-
ting down.

CAUTION: When the System Protection is disabled the system is not pro-
tected against disk corruption or malware attacks. Disable the protection
only for the time necessary to make disk changes.

Содержание AREX 401





















































































































































Результаты поиска

Содержание AREX 401

Отзывы:

Похожие инструкции для AREX 401

Бренды по названию

Популярные бренды

Datalogic AREX 401, Руководство пользователя

Результаты поиска

Содержание AREX 401

Отзывы:

Похожие инструкции для AREX 401

Бренды по названию

Популярные бренды