Datalogic AREX 401 Скачать руководство пользователя страница 76

Страница: 76 / 148

CUSTOMIZE THE LASER MARKER SOFTWARE

AREX™ 401

How to use the System Protection tool

The System Protection tool GUI can be opened:

•

By clicking on the notification popup

•

By right-clicking the tray-bar icon then, “Configure”

•

Double-clicking the tray-bar icon

•

From

Start Menu\Datalogic\System Protection

Enable the system protection

•

Open the System Protection tool GUI

•

Click the

ENABLE

button

•

A message advise the User to confirm the new setting. Press

YES

to enable System

Protection

•

A message advise the User that the system will be rebooted. Press

YES

to continue

NOTE: When the System Protection is enabled any change or deletion on
the C:\ drive will be restored after system reboot.

Содержание AREX 401





















































































































































Результаты поиска

Содержание AREX 401

Отзывы:

Похожие инструкции для AREX 401

Бренды по названию

Популярные бренды

Datalogic AREX 401, Руководство пользователя

Результаты поиска

Содержание AREX 401

Отзывы:

Похожие инструкции для AREX 401

Бренды по названию

Популярные бренды