DataDirect Networks EF3015 Скачать руководство пользователя

Страница: 46 / 59

LED Descriptions

E F 3 0 1 5 S e t u p G u i d e ( R e v A )

A.3

EF3015 Rear Panel LEDs

SERVICE

CACHE

CLI

HOST

2,4G

SERVICE

CACHE

CLI

HOST

2,4G

6Gb/s

Note: Callouts do not tag multiple instances of an identified LED

LED No. /

Description

Color

State

Definition

1 — Power Supply

—

See

A.4 "Power supply LEDs"

2 — Link Status/

Link Activity

(Host 2/4/8 Gb FC)

Green

2,4G LED illuminates — link speed is 2 or 4-Gbps
8G LED illuminates — link speed is 8-Gbps

Off

Both LEDs off — link speed is 1-Gbps

a.The 8 Gb SFP modules do not support 1 Gb link speeds.

Blink

1Hz — no link detected

3 — OK to Remove

Blue

The controller module can be removed.

Off

The controller module is not prepared for removal.

4 — Unit Locator

White

Off

Normal operation.

Blink

Physically identifies the controller module.

5 — FRU OK

Green

Controller module is operating normally.

Off

Controller module is not OK.

Blink

System is booting.

6 — Fault/Service
Required

Yellow

A fault is detected or a service action is required.

Blink

Hardware-controlled power-up, or a cache flush or
restore error.

7 — Network Port
Link Status

Green

The Ethernet link is up.

Off

Ethernet port is not connected or the link is down.

8 — Network Port
Activity

Green

Off

Ethernet link has no I/O activity.

Blink

Ethernet link has I/O activity.

9 — Cache Status

Green

Cache is dirty and operation is normal.

Off

Cache is clean (contains no unwritten data).

Blink

CompactFlash flush or cache self-refresh is in progress,
indicating cache activity.

10 — Expansion
PortStatus

Green

Port is connected and the link is up.

Off

Port is empty or link is down.

NOTE :

Once a Link Status LED is lit, it remains so, even if the controller is shut

down via RAIDar or CLI.

Содержание EF3015




























































Результаты поиска

Содержание EF3015

Отзывы:

Похожие инструкции для EF3015

Бренды по названию

Популярные бренды

DataDirect Networks EF3015, Руководство по установке

Результаты поиска

Содержание EF3015

Отзывы:

Похожие инструкции для EF3015

Бренды по названию

Популярные бренды