Datacom Systems DS-1404 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 55

Datacom Systems DS-1404 Скачать руководство пользователя страница 15

Datacom Systems Inc. 2016

15

DURAstream

™

DS-1404, DS-1406, DS-2408 FASTstart Guide

3 Network IP Address Configuration

All DURAstream™ Bypass Switches can be accessed and configured through the
management port on the front of the unit. Once set up, this port can be used to access the
device through Telnet.

3.1 Default Settings

All DS-X4XX Bypass Switch series units are shipped with a factory default configuration
as follows:

IMPORTANT:

If you expect to remotely connect to the DURAstream™ series, you

must change the IP Address, Subnet Mask and Gateway to match your Local Area
Network.

In order to initially change the IP settings on the management port, you can connect to the
device over the serial port on the front.

Telnet

Port

:

23

Serial Terminal Settings

Bits per second:

115200

Data bits:

8

Parity:

None

Stop:

1

Flow Control:

None

Management Port Settings

IP Address

:

192.168.1.1

Subnet Mask

:

255.255.0.0

Default Gateway

:

192.168.0.1

User Settings

Username:

Administrator

Password:

admin

«
...
13
14
15
16
17
...
»

Содержание DS-1404
























































Отзывы:

Нет отзывов