DataCard CE870 Скачать руководство пользователя

Страница: 14 / 130

Installation

PC Requirements

Use a PC that meets or exceeds the following:



A 32- or 64-bit processor, running at 2GHz or faster



4 GB or more memory (RAM) and at least 1 GB free space on the hard drive



One of the following operating systems:



Windows 10, 32- or 64-bit



Windows 8.1, 32- or 64-bit



Windows 7, 32- or 64-bit



Windows Server 2012, R2, 64-bit



Windows Server 2008, 64-bit



Ethernet network connection



Datacard® CardWizard® issuance software

Ethernet Requirements

The following network components are required:



An Ethernet network that uses the TCP/IP protocol and can run at 100 megabits per second,
also called 100base-T.



An Ethernet cable to connect the system to the network. (An Ethernet cable is not supplied
with the system.)

Electrical Requirements

The power supply is rated as follows:

The power supply detects the input voltage and works within the stated range.

System Component

Electrical Requirements

Input

Output

Printer

110-240V/50–60Hz/1.5 Amp

24V/3.0Amp/72W

Embosser

110-240V/50-60Hz/3.5 Amp,

24V/10.42Amp/250W

Содержание CE870



































































































































Результаты поиска

Содержание CE870

Отзывы:

Похожие инструкции для CE870

Бренды по названию

Популярные бренды

DataCard CE870, Инструкция по установке и руководство администратора

Результаты поиска

Содержание CE870

Отзывы:

Похожие инструкции для CE870

Бренды по названию

Популярные бренды