DataApex Shodex RI-101 Скачать руководство пользователя страница 18

Страница: 18 / 18

Shodex RI-101

6 Troubleshooting

6 Troubleshooting

When the solution to a problem cannot be found easily, a recording of the
communication between

Clarity

and the detector will significantly help

DataApex

support.

The data recording can be enabled by adding or amending the
COMMDRV.INI file in the

Clarity

installation directory (C:\CLARITY\CFG

by default). The file can be edited in any text editor (e.g. Notepad). The
following section should be edited or added:

[COM1]
echo=on
textmode=on
filename=CommDrvCOM1_%D.txt
reset=off

Note:

Instead of COM1, type the communication port used to communicate with
the

Shodex RI-101

detector. This port number is displayed when the

Det

Status

button in the

Method Setup - Acquisition

dialog is invoked.

Note:

(or

) in the filename parameter means that the log will be created

separately for each day. The

reset=off

parameter disables deleting the

content of the log each time the station is started during the same day.

The created *.TXT files will be of great help in the diagnosis of not
documented errors and communication issues.

- 14 -

Содержание Shodex RI-101



















Результаты поиска

Содержание Shodex RI-101

Отзывы:

Похожие инструкции для Shodex RI-101

Бренды по названию

Популярные бренды

DataApex Shodex RI-101, Руководство пользователя

Результаты поиска

Содержание Shodex RI-101

Отзывы:

Похожие инструкции для Shodex RI-101

Бренды по названию

Популярные бренды