DataApex Shodex RI-101 Скачать руководство пользователя страница 16

Страница: 16 / 18

Shodex RI-101

4 Using the control module

4.5 DataApex UNI Setup

The appearance of the

DataApex UNI Setup

dialog depends on the

presence of the selected Ruby Script - if the script is not present, only the

Ruby Script

field is visible.

Fig 9: DataApex UNI Setup

Ruby Script

Displays the selected Ruby Script. The correct SHODEXRI101DET.RB
script for the

Shodex RI-101

detector can be found in the UTILS/UNI_

DRIVERS/SHODEX subdirectory (accessible through the

button) of

the

Clarity

installation folder (C:\CLARITY\BIN by default).

Port

Defines the communication port used, possible values dependent on the
type of communication of the device and/or available ports in the PC.

AutoDetect

It is used for verifying the device communication over the serial port
selected above.

Detector Name

Allows you to set the custom name of the detector. This name (entered
into the

Value

column) will be used throughout the

Clarity

station.

Detector Model

Allows you to set the type of the detector. The selection influences several
settings further in

Method Setup - Acquisition

dialog.

- 12 -

Содержание Shodex RI-101



















Результаты поиска

Содержание Shodex RI-101

Отзывы:

Похожие инструкции для Shodex RI-101

Бренды по названию

Популярные бренды

DataApex Shodex RI-101, Руководство пользователя

Результаты поиска

Содержание Shodex RI-101

Отзывы:

Похожие инструкции для Shodex RI-101

Бренды по названию

Популярные бренды