DataApex Shimadzu GC2014C APC/AFC Скачать руководство пользователя страница 35

Страница: 35 / 35

Shimadzu GC-201x

6 Troubleshooting

6 Troubleshooting

When the remedy for some problem cannot be discovered easily, the
recording of communication between

Clarity

and the chromatograph can

significantly help the

DataApex

support to discover the cause of the

problem.
The recording can be enabled by adding or amending the COMMDRV.INI
file in the

Clarity

installation directory (C:\CLARITY\CFG by default). The

file can be edited in any text editor (e.g. Notepad). Following section
should be edited or added:

[COM1]
echo=on
textmode=on
filename=ShimadzuGC201x.txt; %D or %d could be used to include a
current date (recommended in combination with the Reset=Off option
reset=off

Note:

Instead of COM1 type the correct serial port used to communicate with
the

Shimadzu GC-201x

chromatograph. This port number is displayed

when the

GC Status

button in the

Method Setup - GC

dialog is invoked or

in the

Shimadzu GC-201x Setup

dialog.

The created *.TXT files will greatly help in diagnosis of unrecognized
errors and problems in communication.

- 31 -

Содержание Shimadzu GC2014C APC/AFC




































Результаты поиска

Содержание Shimadzu GC2014C APC/AFC

Отзывы:

Похожие инструкции для Shimadzu GC2014C APC/AFC

Бренды по названию

Популярные бренды

DataApex Shimadzu GC2014C APC/AFC, Руководство пользователя

Результаты поиска

Содержание Shimadzu GC2014C APC/AFC

Отзывы:

Похожие инструкции для Shimadzu GC2014C APC/AFC

Бренды по названию

Популярные бренды