DataApex Clarity INT7 Скачать руководство пользователя страница 8

Страница: 8 / 42

INT7 A/D Converter

3 Installation

3 Installation

Ensure that you have

Administrator

access rights in your

Windows OS

before you proceed with the installation.

3.1 The INT7

Install the

Clarity

software from the DVD-ROM.

Caution:

Install

Clarity

before inputting any devices.

In Windows

2000, XP and later

the drivers were copied to your computer

during the installation of the

Clarity

software.

Clar

Turn off the

Plug the

INT7

card into the

PCI

slot.

Start the

In Windows

2000, XP and later

the drivers were installed automatically

during the installation of the

Clarity

software.

The driver is now installed, proceed to setup and wiring.
Plug in the

key (described in the

Getting Started manual

Note:

When installing multiple

INT7

cards, a PC restart is recommended after

the installation in order to prevent the reassignment of

INT7

acquisition

channels between

Clarity

Instruments.

3.2 Standard cable for Clarity station

Fig 2: Cables for the Clarity station package

The standard

Clarity

station package with

INT7

card includes a cable

composed of signal and starting cables for connecting the

Clarity

station

via the

INT7

card to the chromatograph. The number of signal wires,

starting wires and digital output wires present corresponds to the number
of signals the

INT7

card has - each signal on the card is accompanied by

- 4 -

Содержание Clarity INT7











































Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды

DataApex Clarity INT7, Руководство пользователя

Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды