background image

INT7 A/D Converter

5 Troubleshooting

5.4 Data Acquisition - non-functional

▌ Gray

icon with the heading

DISABLED

and non- functional

Monitor - Data

Acquisition

command.

Fig 33: Data Acquisition disabled

Other manifestations of this error are also:

Method Setup - Acquisition

tab missing,

Method - Acquisition

command non-functional,

Run

,

Stop

,

Abort

and other similar

commands non- functional in the

Single Analysis

,

Sequence

or

Device Monitor

windows. Possible causes are:

Description:

a) You are using

Clarity Offline

or a

Clarity DEMO

version, which does not

enable the measurement of chromatograms.

Fig 34: Clarity Offline and Clarity DEMO

Solution:

Check whether there is a blue line with the title

OFFLINE

displayed in the main

Clarity

window under the symbols of the Instruments, or the title

DEMO

in the

Clarity

window header.

In case of

Clarity DEMO

, use the

Windows Start menu

to locate the

Clarity

DEMO

group in the

All Programs

section and select the

Remove Clarity

item there.

Then, use the correct

Clarity

installation DVD to install the full version.

In case of the

Clarity Offline

station, remove the HW key with the

Offline

license

and insert key with the

Clarity

full licence.

Description:

b) Detector is not allocated to the

Clarity

Instrument:

Fig 35: Detector not allocated to the Instrument

Solution:

Open the

System Configuration

dialog from the

Clarity

window using the

System -

Configuration...

command and check the tab of the corresponding Instrument -

Instrument X

. If it has no allocated detectors, add them.

In the left-hand list

Setup Control Modules

select the correct detector connected to

the

A/D card

you are using and drag it to the corresponding instrument on the

right.

- 32 -

Содержание Clarity INT7











































Отзывы: