Data General AViiON 5500 Series Скачать руководство пользователя

Страница: 159 / 192

System board and system bus options

A-3

014–002250–01

Expansion CPU complex board (optional)

One 40–megahertz Motorola 88110 32–bit RISC microprocessor
with integral floating–point unit

One Motorola 88410 CMMU

Stacked on system board with one 200–pin impedance–controlled
connector

Expansion input/output board (optional)

Maximum of two (AViiON 5500 series) or one (AViiON 550 series) of
the following option boards stacked on system board with two
96–pin DIN connectors

NCR SCSI adapter board with two integrated controllers

AMD 802.3 Ethernet LAN controller

Graphics controller board (AViiON 550 series)

One 8– or 24–bit/pixel color graphics subsystem board provides high
resolution display. The following summarizes some features of both
controllers:

32–bit wide address/data bus

70 Hz refresh

1280 x 1024 displayable resolution

3–color hardware cursor

4 Mbit video DRAMs (256K x 16)

Stacks on system board with two 96–pin DIN connectors

KMA (keyboard/mouse/audio) controller supports standard AT
keyboard and serial mouse. NOTE: Audio input/output is
NOT SUPPORTED.

8–bit controller (base system)

8 bits/pixel

Bt459 RAMDAC

256 active colors from palette of 16.7 million

Two overlay planes

3–color hardware cursor

24–bit controller

24 bits/pixel

Bt463 RAMDAC

True color display from a 16.7–million color palette

Dynamic, per–pixel allocation of planes and visual modes

2–color hardware cursor

Содержание AViiON 5500 Series

































































































































































































Результаты поиска

Содержание AViiON 5500 Series

Отзывы:

Похожие инструкции для AViiON 5500 Series

Бренды по названию

Популярные бренды

Data General AViiON 5500 Series, Установка, расширение и обслуживание

Результаты поиска

Содержание AViiON 5500 Series

Отзывы:

Похожие инструкции для AViiON 5500 Series

Бренды по названию

Популярные бренды