background image

P

AGE

 12

12 P

AGES

46023-12-0399 <90-00009>

L

IMITED

 W

ARRANTY

The Seller warrants that the standard hardware products sold will be free from defects in material and

workmanship and perform to the Seller’s applicable published specifications for a period of 18 months for

hardware, and 3 months for software, from the date of the original invoice. The liability of the Seller hereunder

shall be limited to replacing or repairing, at its option, any defective products which are returned F.O.B. to the

Seller’s plant, (or, at the Seller’s option, refunding the purchase price of such products). In no case are products

to be returned without first obtaining permission and a customer return authorization number from the Seller.

In no event shall the Seller be liable for any consequential or incidental damages.
Equipment or parts which have been subject to abuse, misuse, accident, alteration, neglect, unauthorized

repair or installation are not covered by warranty. The Seller shall make the final determination as to the

existence and cause of any alleged defect. No warranty is made with respect to custom equipment or products

produced to the Buyer’s specifications except as specifically stated in writing by the Seller in the contract for

such custom equipment.
This warranty is the only warranty made by the Seller with respect to the goods delivered hereunder, and may

be modified or amended only by a written instrument signed by a duly authorized officer of the Seller and

accepted by the Buyer.
Warranty and remedies on products not manufactured by the Seller are in accordance with warranty of the

respective manufacturer. THE SELLER MAKES NO OTHER WARRANTY OF ANY KIND WHATSOEVER,

EXPRESSED OR IMPLIED; AND ALL IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PUR-

POSE WHICH EXCEEDS THE AFORESAID OBLIGATIONS IS HEREBY DISCLAIMED BY THE SELLER.

I

N

 C

ASE

 

OF

 D

IFFICULTY

If you experience difficulty with this equipment, check the following, as appropriate:

1. Switch settings

2. Signal levels

3. Software configuration

4. Connections between Dantel’s equipment and your equipment.

If there is still a problem, substitute equipment that is known to be good. For additional assistance, call

Dantel’s Technical Field Service Department weekdays, 6 

A

.

M

. to 5 

P

.

M

. pacific time:

1-800-4DANTEL (1-800-432-6835).

If a thorough checkout shows a piece of equipment has malfunctioned, you may return it to the factory. For

repairs and emergency replacements, obtain a Return Material Authorization (RMA) number from the Cus-

tomer Service Representative at 

1-800-4DANTEL

 (1-800-432-6835).

To ensure expedient processing of your order, provide a purchase order number and shipping and billing

information when requesting an RMA number. Also, when the units are returned to Dantel, include a descrip-

tion of the failure symptoms for each unit returned. Send defective equipment to:

Dantel, Inc.

2991 North Argyle Avenue

Fresno, California 93727-1388

P.O. Box 55013 • Fresno, CA 93747-5013

Phone (559) 292-1111

Fax (559) 292-9355

http://www.dantel.com

WARRANTY

Содержание 46023-12













Отзывы: