Dannmar DLR-6 Скачать руководство пользователя | Manualshive

Страница: 8 / 40

background image

DLR-6/6P Low-Rise Scissor Lifts

8

P/N 5900254 — Rev. A — September 2020

Installation

This section describes how to install your DLR-6/6P. Perform the steps in the order listed.

⚠

DANGER

Be very careful when setting up, operating, maintaining, or repairing this equipment;
failure to do so could result in property damage, product damage, injury, or (in very

rare cases) death. Make sure only authorized personnel operate this equipment. All

repairs must be performed by an authorized technician. Do not make modifications

to the unit; this voids the warranty and increases the chances of injury or property
damage. Make sure to read and follow the instructions on the labels on the unit.

Some installation steps are the same for both Lift models, but some are different.

⚠

WARNING

Only use the factory-supplied parts that came with your Lift

. If you use

parts from a different source, you void your warranty and compromise the safety of
everyone who installs or uses the Lift. If you are missing parts, visit

dannmar.com/support

or call

(877) 432-6627

.

Safety Rules

When installing the Lift, your safety depends on proper training and thoughtful operation.

⚠

WARNING

Do not install this equipment unless you have automotive Lift installation training.

Always use proper tools, such as a Forklift or Shop Crane, to move heavy

components. Do not install this equipment without reading and understanding this

Manual and the safety labels on the unit.

We recommend referring to the ANSI/ALI ALIS Standard (R2015)

Safety Requirements for Installation

and Service

for more information about safely installing, using, and servicing your Lift.

Only trained, supervised personnel should be involved in installing this equipment.

Pay attention at

all times.

Use appropriate tools and equipment. Stay clear of moving parts.

⚠

WARNING

You

must

wear OSHA-approved (publication 3151) Personal Protective Equipment

at all times when installing the Lift. Leather gloves, steel-toed work boots, eye
protection, back belts, and hearing protection

are mandatory

.

Tools

You may need some or all of the following tools:
•

Hammer, mallet, crowbar, or pry bar

•

Hex key and wrench set, metric and SAE

•

Screwdriver set, slot and Phillips

•

Level, tape measure

•

Adjustable crescent wrench

•

Utility knife, tin or sheet metal snips

•

Screwdriver set, slot and Phillips

•

Forklift or Shop Crane

•

Rotary Hammer Drill, Masonry Bits

«
...
6
7
8
9
10
...
»

Содержание DLR-6









































Отзывы:

Нет отзывов

Похожие инструкции для DLR-6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды