manualshive.com logo in svg

Danfoss Weatherhead COLL-O-CRIMP T-480, Руководство по установке и эксплуатации, Страница: 13 / 14

Поделиться
Скачать
Danfoss Weatherhead COLL-O-CRIMP T-480 Скачать руководство пользователя страница 13

 

13 | PORTABLE COLL-O-CRIMP® Model T-480  Set up and operating instructions | 2022.10.

BC425482205281en-000101

Repair & Replacement Items

Item Number Qty.

Part Number

Description

Remarks

1

1

T-480-P

Pusher

2

1

T-480-PSK

Pusher Stop Repair Kit

Includes pusher clip, 2 machine screws, pusher 
stop & spring

3

1

T-480-SP

Slider Plate

4

2

140-05485-01

Roll Pin

5

1

T-480-SFK

Slide Flange Kit

Includes slide flange, 2 bushings & 2 machine 
screws

6

1

T-480-SPR

Slide Pull Rod

7

1

T-480-SPK

Slide Pull Knob

8

2

140-06601

Vinyl Grip

9

1

T-480-TBK

Tilt Bracket Knob

10

6

140-06894

Foot Pad

11

1

T-480-69

Tool Locator Bracket

#

1

T-480-70

Hose Assembly

10,000 PSI replacement hose assembly for T-
480-HP and T-480-AH System

#

1

T-480-71

Hose Assembly

10,000 PSI replacement hose assembly for T-
480-EP and T-480-TA System

#

1

140-06906

Hydraulic Quick Coupler

Used with the T-480-TA and T-480-EP System

#

1

T-480-3

Turbo Air/Hydraulic Pump

Replacement pump for T-480-TA System

#

1

T-481-110

Electric Pump

Replacement pump for T-480-EP System

#

1

T-480-2

Hand Pump

Replacement pump for T-480-HP System

#

1

T-482-2

Air/Hydraulic Pump

Replacement pump for T-480-AH System

#

1

T-480-M

Set-up & Operating Guide

For T-480 System

# Item not illustrated in parts breakdown.

Содержание Weatherhead COLL-O-CRIMP T-480















Отзывы:

Нет отзывов