Danfoss VLT Soft Starter MCD 600 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 34

Danfoss VLT Soft Starter MCD 600 Скачать руководство пользователя страница 20

•
•

Bits

Function

Details

68930d (0x10D42) = 689.30 A

7.1.3.4 Bytes 8–9: Trip Code

Bits

Function

Details

0–15

Trip code

See the chapter

Trip Codes

.

7.1.3.5 Bytes 10–11: Reserved

Bits

Function

Details

0–15

Reserved

7.2 Explicit Messaging (Acyclic Operation)

This section provides information on objects, instances, attributes, and services for acyclic operation (explicit messaging).
All data is in little endian format.

7.2.1 Identity Object (Class 0x01)

Table 5: Supported Attributes for Identity Objects

Attribute

Function

Value

1

Vendor

204d (0xCC)

2

Device type

12d (0x0C)

3

Product code

269d (0x10D)

4

Revision: Major, minor

EDS file version

5

Status

Supported

6

Serial number

Supported

7

Product name

Supported

7.2.2 Vendor-specific Objects

The EtherNet/IP Card supports vendor-specific classes 100, 101, 103, and 104.

7.2.2.1 Class 100 and 101 Objects (Read/Write)

Class 100 and 101 objects allow parameter values to be read from and written to the soft starter.

Class 100d (0x64): Parameters 1–99
Class 101d (0x65): Parameters 100–199

See the chapter

Parameter Lists

for more details.

7.2.2.2 Class 103 Objects (Read Only)

Class 103d (0x67) allows soft starter state information to be read from the soft starter.

N O T I C E

For models MCD6-0063B and smaller, current reported via communications is 10 times greater than the actual value shown on
the LCP.

AN353423548483en-000101 / 130R0945

20 | Danfoss A/S © 2020.12

Messaging

EtherNet/IP Card

Installation Guide

«
...
18
19
20
21
22
...
»

Содержание VLT Soft Starter MCD 600



































Отзывы:

Нет отзывов