Danfoss VLT OneGearDrive Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 44

Danfoss VLT OneGearDrive Скачать руководство пользователя страница 6

•

•

•

•

•

•

•

•

•

•

-

-

1 Introduction

1.1 Purpose of the Operating Guide

The purpose of this Operating Guide is to describe the VLT® OneGearDrive®. The Operating Guide contains information about:

Safety

Installation

Commissioning

Maintenance and repair

Specifications

Options and accessories

The VLT® OneGearDrive® is available with 2 different motor types:

LA10 (type code L09), service period since August 2015.

V210 (type code L06), since August 2015.

Check the motor type on the nameplate.

N O T I C E

If exchanging a VLT® OneGearDrive® with LA10 motor type with a V210 motor type, always ensure to update the motor mod-
el in the drive, see

9.3 Technical Data: Permanent Magnet 3-phase Synchronous Motor

. Contact Danfoss Service for further

instructions.

N O T I C E

For reasons of clarity, the instructions and safety information do not contain all information relating to all VLT® OneGear-
Drive® types and cannot take into account every conceivable case of installation, operation, or maintenance. The information
is limited to that which is required for qualified personnel in normal working situations. Contact Danfoss for further assis-
tance.

This Operating Guide is intended for use by qualified personnel. Read this operating guide in full in order to use the VLT® OneGear-
Drive® safely and professionally. Pay particular attention to the safety instructions and general warnings.
This Operating Guide is a part of the VLT® OneGearDrive® and also contains important service information. Always keep this Operat-
ing Guide available with the VLT® OneGearDrive®.
Compliance with the information in this Operating Guide is a prerequisite for:

Trouble-free operation.

Recognition of product liability claims.

Therefore, read this Operating Guide before working on or with the VLT® OneGearDrive®.

1.2 Copyright

VLT

®

and OneGearDrive

®

are Danfoss registered trademarks.

1.3 Approvals

Table 1: Approvals

(depending on the configuration)

AQ347551551757en-000101 / 130R0239

6 | Danfoss A/S © 2020.12

Introduction

VLT® OneGearDrive®

Operating Guide

«
...
4
5
6
7
8
...
»

Содержание VLT OneGearDrive













































Отзывы:

Нет отзывов