manualshive.com logo in svg

Danfoss VLT MCA 121 EtherNet/IP, Руководство пользователя

Поделиться
Скачать
Danfoss VLT MCA 121 EtherNet/IP Скачать руководство пользователя страница 33

8-14  Configurable Control Word CTW

Option:

Function:

Selection of control word bit 10 if it is active low or active high

[0]

None

[1] *

Profile default

[2]

CTW Valid, active low

8-50  Coasting Select

Option:

Function:

Select control of the coasting function via the terminals (digital input) and/or via the bus.

[0]

Digital input

[1]

Bus

Activates Start command via the serial communication port or fieldbus option.

[2]

Logic AND

Activates Start command via the fieldbus/serial communication port, AND additionally via one of the
digital inputs.

[3] *

Logic OR

Activates Start command via the fieldbus/serial communication port OR via one of the digital inputs.

NB!

This parameter is active only when par.8-01 

Control Site

 is set to [0] 

Digital and control word

.

MCA 121 EtherNet/IP

6 Parameters

MG.90.J2.02 - VLT

®

 is a registered Danfoss trademark

33

  6

Содержание VLT MCA 121 EtherNet/IP






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды