Danfoss VLT HVAC Basic Drive FC 101 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 104

background image

3.16 Main Menu - Application Functions 2 -

Group 24

3.16.1 24-0* Fire Mode

CAUTION

Note that the frequency converter is only one
component of the system. Correct function of Fire Mode
depends on the correct design and selection of system
components. Ventilation systems working in life safety
applications have to be approved by the local fire
Authorities. Non-interruption of the frequency converter
due to Fire-Mode operation could cause over pressure
and result in damage to the system and components,
hereunder dampers and air ducts. The frequency
converter itself could be damaged and it may cause
damage or fire. Danfoss accepts no responsibility for
errors, malfunctions personal injury or any damage to
the frequency converter itself or components herein,
systems and components herein or other property when
the frequency converter has been programmed for Fire
Mode. In no event shall Danfoss be liable to the end user
or any other party for any direct or indirect, special or
consequential damage or loss suffered by such party,
which has occurred due to the frequency converter
being programmed and operated in Fire Mode.

Background

Fire Mode is for use in critical situations, where it is
imperative for the motor to keep running, regardless of
the frequency converter’s normal protective functions.
These could be ventilation fans in tunnels or stairwells for
instance, where continued operation of the fan facilitates
safe evacuation of personnel in the event of a fire. Some
selections of Fire Mode Function cause alarms and trip
conditions to be disregarded, enabling the motor to run
without interruption.

Activation

Fire Mode is activated only via Digital Input terminals. See
parameter group

5-1* Digital Inputs

.

Messages in display

When Fire Mode is activated, the display shows a status
message “Fire Mode”.
Once the Fire Mode is again deactivated, the status
message disappears.
If, while the frequency converter is active in Fire Mode, a
warranty-affecting alarm (see

24-09 FM Alarm Handling

)

occurs, the display shows the status message “Fire Mode
Limits Exceeded”. Once this status message appears, it
remains permanently, and cannot be removed.
Digital and relay outputs can be configured for the status
messages “Fire Mode Active”. See parameter group

5-3*

Digital Outputs

and parameter group

5-4* Relays

.

The status messages “Fire Mode” and “Fire Mode Limits
Exceeded” can be accessed via the extended status word.

Message

Type

LCP Message

Warning

Word 2

Ext. Status

Word 2

Fire Mode

Status

+

+

+ (bit 25)

Fire Mode
Limits
Exceeded

Status

+

+

Table 3.11 Fire Mode Display Messages

Log

An overview of events related to Fire Mode can be viewed
in the Fire Mode log, parameter group

18-1* Fire Mode Log

.

The log includes up to 10 of the latest events.

Fire Mode

Limits Exceeded

has a higher priority than

Fire Mode Active

.

The log cannot be reset.
Following events are logged:
*Warranty affecting alarms (see

24-09 FM Alarm Handling

,

Fire Mode Alarm Handling)
*Fire Mode Activated
*Fire Mode Limits Exceeeded
All other alarms occurring while Fire Mode activated are
logged as usual.

NOTICE

During Fire Mode operation all stop commands to the
frequency converter are ignored, including Coast/Coast
inverse and External Interlock.

NOTICE

If setting the command

[11] Start Reversing

on a digital

input terminal in

5-10 Terminal 18 Digital Input

, the

frequency converter understands this as a reversing
command.

24-00 FM Function

Option:

Function:

[0]

*

Disabled

Fire Mode Function is not active.

[1]

Enabled-Run
Forward

In this mode the motor will continue to
operate in a clockwise direction.

[2]

Enabled-Run
Reverse

In this mode the motor will continue to
operate in a counter-clockwise direction.

[3]

Enabled-Coast

Whilst this mode is enabled, the output is
disabled and the motor is allowed to
coast to stop.

[4]

Enabled-Run
Fwd/Rev

NOTICE

In the above, alarms are produced or ignored in
accordance with the selection in

24-09 FM Alarm

Handling

.

Parameters

VLT

®

HVAC Basic Drive FC 101 Programming Guide

78

MG18B302 - Rev. 2013-09-02

3

3

«
...
78
79
80
81
82
...
»

Содержание VLT HVAC Basic Drive FC 101









































































































Отзывы:

Нет отзывов

Похожие инструкции для VLT HVAC Basic Drive FC 101

Бренд: Danfoss Страницы: 54

Бренд: Danfoss Страницы: 34

Бренд: Danfoss Страницы: 197

Бренд: Danfoss Страницы: 284

Бренд: Danfoss Страницы: 53

MELDAS HS Series

Бренд: Mitsubishi Страницы: 133

Бренд: Parker Страницы: 54

L-force EYP Series

Бренд: Lenze Страницы: 8

Бренд: AB Quality Страницы: 32

BLD-YT08D Series

Бренд: superbrightleds Страницы: 3

Бренд: Kanguru Страницы: 9

Fcontrol FKDM..-C Series

Бренд: ZIEHL-ABEGG Страницы: 99

Бренд: Eurotherm Drives Страницы: 94

Бренд: Eurotherm Drives Страницы: 176

Бренд: Applied Motion Products Страницы: 2

Бренд: PR electronics Страницы: 62

Бренд: TECO Страницы: 255

Бренд: Melec Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды