background image



1 Introduction

1.1 Purpose of this Programming Guide

This Programming Guide provides information on working with parameters on the VLT® Flow Drive FC 111 drive.
It provides information on how to programme the drive, and a list and description of all parameters.
VLT

®

 is a registered trademark for Danfoss A/S.

1.2 Additional Resources

1.2.1 Other Resources

Other resources are available to understand advanced drive functions and programming.

VLT® Flow Drive FC 111 Operating Guide provides basic information on mechanical dimensions, installation, and programming.
VLT® Flow Drive FC 111 Design Guide provides information on how to design motor control systems.
Danfoss VLT® Energy Box software. Select PC Software Download at 

www.danfoss.com

.

VLT® Energy Box software allows energy consumption comparisons of HVAC fans and pumps driven by Danfoss drives and alterna-
tive methods of flow control. Use this tool to accurately project the costs, savings, and payback of using Danfoss drives on HVAC
fans, pumps, and cooling towers.
Supplementary publications and manuals are available from Danfoss website.

1.2.2 MCT 10 Set-up Software Support

Download the software from the service and support section on 

www.danfoss.com

.

During the installation process of the software, enter access code 81462700 to activate the VLT® Flow Drive FC 111 functionality. A
license key is not required for using the VLT® Flow Drive FC 111 functionality.
The latest software does not always contain the latest updates for drives. Contact the local sales office for the latest drive updates (in
the form of *.OSS files).

1.3 Document and Software Version

This guide is regularly reviewed and updated. All suggestions for improvement are welcome.
The original language of this manual is English.

Table 1: Document and Software Version

Edition

Remarks

Software version

AU363928304090, version 0101

First edition.

6x.xx

1.4 Electrical Wiring

AU363928304090en-000101 / 130R0982 | 5

Danfoss A/S © 2021.07

Introduction

VLT® Flow Drive FC 111

Programming Guide

Содержание VLT Flow Drive FC 111























































































































































































































Отзывы: