Danfoss VLT FCD 303 Скачать руководство пользователя страница 88

Страница: 88 / 127

VLT

FCD Series

■

Serial communication

500 Address

(BUS ADDRESS)

Value:

Parameter 500 Protocol = FC protocol [0]

0 - 247

✭

Parameter 500 Protocol = Metasys N2 [1]

1 - 255

✭

Parameter 500 Protocol = MODBUS RTU [3]

1 - 247

✭

Function:

This parameter allows the allocation of an

address to each frequency converter in a serial

communication network.

Description of choice:

The individual frequency converter must be

allocated a unique address.

If the number of units connected (frequency converters

+ master) is higher than 31, a repeater must be used.

Parameter 500

Address

cannot be selected

via the serial communication, but must be

preset via the control unit.

501 Baudrate

(BAUDRATE)

Value:

300 Baud (300 BAUD)

[0]

600 Baud (600 BAUD)

[1]

1200 Baud (1200 BAUD)

[2]

2400 Baud (2400 BAUD)

[3]

4800 Baud (4800 BAUD)

[4]

✭

9600 Baud (9600 BAUD)

[5]

Function:

This parameter is for programming the speed at which

data is transmitted via the serial port. Baud rate is

defined as the number of bits transmitted per second.

Description of choice:

The frequency converter

’

s transmission speed

must be set at a value corresponding to the

transmission speed of the master.

Parameter 501

Baudrate

cannot be selected via the

serial port, but must be preset via the operating unit.

502 Coasting Stop

(COASTING SELECT)

Value:

Digital input (DIGITAL INPUT)

[0]

Serial port (SERIAL PORT)

[1]

Logic and (LOGIC AND)

[2]

✭

Logic or (LOGIC OR)

[3]

Function:

Parameters 502-508 allow a choice between

controlling the frequency converter via the digital

inputs and/or via the serial port.

Serial port

[1] is selected, the relevant

command can only be activated if a command

is given via the serial port.

In the case of

Logic and

[2] the function must

also be activated via a digital input.

Description of choice:

The table below shows when the motor is running

and when it is coasting, when each of the

following is selected:

Digital input

[0],

Serial port

[1],

Logic and

[2] or

Logic or

[3].

NB!:

Note that

Coasting stop

and Bit 03 in the

control word are active at logic

’

Digital input

[0]

Dig. input

Ser. port

Function

Coasting

Motor running

Serial port

[1]

Dig. input

Ser. port

Function

Coasting

Motor running

Coasting

Motor running

Logic and

[2]

Dig. input

Ser. port

Function

Coasting

Motor running

✭

= factory setting. () = display text [] = value for use in communication via serial communication port

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды