Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 16 / 127

VLT

FCD Series

■

Mains connection

No. 91 92

Mains voltage 3 x 380-480 V

Earth connection

NB!:

Please check that the mains voltage fits the

mains voltage of the frequency converter, which

can be seen from the nameplate.

See

Technical data

for correct dimensioning

of cable cross-section.

■

Pre-fuses

See

Technical data

for correct dimensioning

of pre-fuses.

■

Motor connection

Connect the motor to terminals 96, 97, 98.

Connect earth to PE-terminal.

No.

Motor voltage 0-100% of mains voltage

3 wires out of motor

6 wires out of motor, Delta connected

6 wires out of motor, Star connected

U2, V2, W2 to be interconnected

separately (optional terminal block)

Earth connection

See

Technical data

for correct dimensioning

of cable cross-section.

All types of three-phase asynchronous standard

motors can be connected to a frequency converter.

Normally, small motors are star-connected (230/400

/ Y). Large motors are delta-connected (400/690

/ Y). The correct connection mode and voltage

can be read from the motor nameplate.

NB!:

In motors without phase insulation paper,

an LC filter should be fitted on the output

of the frequency converter.

■

Direction of motor rotation

The factory setting is for clockwise rotation

with the frequency converter transformer output

connected as follows:

Terminal 96 connected to U-phase.

Terminal 97 connected to V-phase.

Terminal 98 connected to W-phase.

The direction of rotation can be changed by switching

two phases on the motor terminals.

■

Mains and motor connection with service switch

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды