background image

6.5 General Technical Data

6.5.1 Protection and Features

Electronic motor thermal protection against overload.

Temperature monitoring of the heat sink ensures that the drive trips if there is overtemperature.

The drive is protected against short circuits between compressor terminals U, V, W.

When a compressor phase is missing, the drive trips and issues an alarm.

When a mains phase is missing, the drive trips or issues a warning (depending on the load).

Monitoring of the DC-link voltage ensures that the drive trips when the DC-link voltage is too low or too high.

The drive is protected against ground faults on compressor terminals U, V, W.

6.5.2 Mains Supply (L1, L2, L3)

Supply voltage

200–240 V ±10%

Supply voltage

380–480 V ±10%

Supply frequency

50/60 Hz

Maximum imbalance temporary between mains phases

3.0% of rated supply voltage

True power factor (λ)

≥0.9 nominal at rated load

Displacement power factor (cosφ) near unity

(>0.98)

Switching on the input supply L1, L2, L3 (power-ups)

Maximum 2 times/minute

Environment according to EN 60664-1

Overvoltage category III/pollution degree 2

The unit is suitable for use on a circuit capable of delivering not more than 100000 A

rms

symmetrical Amperes, 240/480 V maximum.

6.5.3 Compressor Output (U, V, W)

Output voltage

0–100% of supply voltage

Output frequency

0–200 Hz (VVC

+

), 0–400 Hz (u/f)

Switching on output

Unlimited

Ramp times

0.05–3600 s

6.5.4 Cable Lengths and Cross-sections

Maximum compressor cable length, shielded/armored (EMC-correct installation)

See 

6.3 EMC Emission Test Results

.

Maximum compressor cable length, unshielded/unarmoured

50 m (164 ft)

Maximum cross-section to compressor, mains

See 

6.2 Mains Supply 3x380–480 V AC

 for more

information

Cross-section DC terminals for filter feedback on enclosure size H3

4 mm

2

/11 AWG

Cross-section DC terminals for filter feedback on enclosure sizes H4–H6

16 mm

2

/6 AWG

Maximum cross-section to control terminals, rigid wire

2.5 mm

2

/14 AWG

Maximum cross-section to control terminals, flexible wire

2.5 mm

2

/14 AWG

Specifications

Operating Guide  | VLT® Compressor Drive CDS 803

AQ321748767627en-000101 / 130R0570

46 | Danfoss A/S © 2019.12

Содержание VLT CDS 803























































Отзывы: