Danfoss VLT AutomationDrive FC 360 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 31

Danfoss VLT AutomationDrive FC 360 Скачать руководство пользователя страница 30

Index

Abbreviations........................................................................................... 2

Convention................................................................................................ 2

Diameter measurement signal.......................................................... 8
Discharge time......................................................................................... 4
Document version.................................................................................. 2

High altitude............................................................................................. 5
High voltage............................................................................................. 4

Initial diameter measurement............................................................ 8

Leakage current....................................................................................... 5
Line speed.................................................................................................  8
Load sharing.............................................................................................  4
Logic input................................................................................................  8

Over-tension............................................................................................. 9

PELV............................................................................................................. 5

Qualified personnel................................................................................ 4

Safety........................................................................................................... 5
Software version...................................................................................... 2

Taper setpoint.......................................................................................... 8
Tension and taper setpoint................................................................. 8
Tension feedback............................................................................... 6, 8
Tension setpoint...................................................................................... 8

Unintended start..................................................................................... 4

Winder speed........................................................................................... 8
Winder speed match scale................................................................... 9

Index

Application Guide

MG06E102

Danfoss A/S © 11/2014 All rights reserved.

29

«
...
28
29
30
31
»

Содержание VLT AutomationDrive FC 360
































Отзывы:

Нет отзывов