Danfoss VLT 5000 Crane Series Скачать руководство пользователя страница 92

Страница: 92 / 123

VLT® 5000 Crane

All About VLT 5000

Crane

■

Warnings and Alarms, 29-49

Warn-

ings/Alarm

numbers

Display

Description

How to Handle

29 (w)

Heat Sink Over Temp

For IP20/IP 00, the cut-out temperature if the heat

sink is 90°C. The tolerance is +/- 5°C.

Decrease ambient temperature and

check fans

30 (a)

Missing Mot.Phase U

Motor phase U between frequency converter and

motor is missing

Turn off the frequency converter and

check motor phase U

31 (a)

Missing Mot.Phase V

Motor phase V between frequency converter and

motor is missing

Turn off the frequency converter and

check motor phase V

32 (a)

Missing Mot.Phase

Motor phase W between frequency converter and

motor is missing

Turn off the frequency converter and

check motor phase W

35 (w)

Motor Not Ready

The drive was unable to finish the starting sequence

(pre-magnetisation and start torque) within 5 sec.

Check the motor connection

37 (a)

Inverter Fault

IGBT or the power card is defective

Contact your Danfoss supplier

43 (a)

Brake Fault

A fault has arisen on the brake chopper. The text

shown in the display indicates a fault message.

The figure in square brackets is the fault code that

can be seen in the fault log, parameter 615

[0] The brake resistor check carried out

during power-up indicates that the brake

has been disconnected. Check whether

the brake has been connected correctly

and that it has not been dispconnected

[1] The brake output has short-circuited.

Replace the brake resistor

[2] The brake IGBT has short-circuited.

This fault means that the unit is not able

to stop the brake and that, consequently,

the resistor is constantly being energized

44 (a)

Encoder fault

The encoder signal is interrupted from terminal 73,

74, 75, 76, 77 or 78

Check the connections

45 (a)

Load fault

An overload has occurred on one or both of the

load contacts and the speed is too high to hold the

load. The overload causes a trip

Start up again with reduced speed

46 (a)

Watchdog fault

An internal error has occurred

Contact your Danfoss supplier

47 (a)

Flash fault

An internal error has occurred

Contact your Danfoss supplier

48 (a)

Tracking fault

Load is dropping faster than expected

Check mechanical brake

49 (w)

Brake release fault

Fault when releasing the brake (open).

50 (w)

Brake activate fault

Fault when activating the brake (close)

Remove the start signal

MG.50.N4.02 - VLT is a registered Danfoss trademark

Содержание VLT 5000 Crane Series




























































































































Результаты поиска

Содержание VLT 5000 Crane Series

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLT 5000 Crane Series, Руководство по эксплуатации

Результаты поиска

Содержание VLT 5000 Crane Series

Отзывы:

Бренды по названию

Популярные бренды