manualshive.com logo in svg

Danfoss TMM 070, Руководство по обслуживанию

Поделиться
Скачать
Danfoss TMM 070 Скачать руководство пользователя страница 24

C – Anti-cavitation valve

F – Shaft seal

Shaft Seal Replacement

The shaft seal is serviceable. Orient the motor on the work surface so the shaft is pointing up.

Removal

1. Using snap-ring pliers, remove the outer snap-ring (B110).
2. Remove the washer (B100)
3. Use 2 screwdrivers to remove the shaft seal (B90). Discard the seal.

C

Caution

Do not damage the housing bore, shaft or bearing when removing the seal.

Inspection

Inspect the housing bore, shaft and bearing. If you find any defect, replace damaged component.

Reassembly

1. Press the shaft seal (B090) with seal installation tool into housing.
2. Install the remaining washer (B100).
3. Install the remaining snap-ring (B110).

Shaft seal assembly

B110

d

B100

B090

B065

High Pressure Relief Valves (HPRV)

Removal

Using a 12 mm internal hex wrench, remove the HPRVs (G090). Remove and discard the O-rings

(G090A).

Inspection

Inspect the sealing surfaces in the motor for nicks or scratches. Check the valves for damage. Replace

any damaged components.

Service Manual

TMM Transit Mixer Axial Piston Motor, Size 070/084/089

Minor Repair

24

L1211037 • Rev AC • Apr 2014

Содержание TMM 070

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды