background image

Danfoss District Energy 

 

 

 

 

VI.SH.K1.02 

 

 

 

               DEN-SMT/PL

1

Instruction

1.0   Table of contents

SONOMETER™ 1100

Ultrasonic compact energy meter

2.0  Safety notes and product information

1.0  

Table of contents

 .........................................................................................................................................................................................................................................................................

1

2.0  

Safety notes and product information

 ........................................................................................................................................................................................................................

1

3.0  

Installation of energy meter

 ................................................................................................................................................................................................................................................

2

4.0  

Installation of temperature sensors

 ...............................................................................................................................................................................................................................

3

5.0  

Power  supply

 ..................................................................................................................................................................................................................................................................................

4

6.0  

Start-up  operation

 ......................................................................................................................................................................................................................................................................

5

7.0  

Expansion  modules

 ...................................................................................................................................................................................................................................................................

5

8.0  

Communication

 ...........................................................................................................................................................................................................................................................................

6

9.0  

Display

 .................................................................................................................................................................................................................................................................................................

8

10.0  Simple operation

 .........................................................................................................................................................................................................................................................................

9

11.0  Error codes

 .......................................................................................................................................................................................................................................................................................

9

 

Following instructions refer to the ultrasonic energy meter.

The regulations on the use of energy meters must be observed! The 
meter installation is only to be performed by an installation and/
or electrical contractor using personnel trained in the installation 
and use of electrical equipment and familiar with the Low Voltage 
Directive.

- Medium: water, as per AGFW Instruction Sheet FW510.If water 

additives are used (e.g. corrosion protection), the user must 
make sure that the corrosion resistance is adequate.

- The specified medium temperature 

is 5 ... 90°C/105°C/130°C(150°C)

- The temperature range depends on variant and nominal size
- The exact temperature range is shown on the type plate
- The encapsulated variant is to be used if condensation is 

expected

- The specified operating/ambient conditions are: 

5…55 °C; max. 93% rel. humidity

- Protection class: calculator IP54; flow sensor 

IP54 (heating)/IP65 (cooling, heat/cooling)

- Ambient temperatures below 35 °C ensures typical battery 

lifetime

This installation guide is intended for trained personnel and 
does not contain any basic working steps.

If the flow sensor is insulated with the pipeline, 
the calculator must be accessible.

Safety Note

The seal on the energy meter must not be damaged! 
A damaged seal will result in immediate invalidation of the 
factory warranty and verification. The cables supplied with the 
meter must not be shortened, extended or changed in any 
other way.

Содержание SONOMETER 1100











Отзывы: