Danfoss Series 45 страница 38 Скачать руководство пользователя

Страница: 38 / 44

5. Check magnet carrier for cracks , deformations, wearing, and for contamination with magnetic

particles

Warning

A thorough inspection with the angle sensor removed is a strong indicator of pump and hydraulic

system contamination and filtration quality.

Reassembly

1. Using new magnet carrier screws with locking compound (K115) install the magnet carrier (K105) to

pump swashplate through the housing. Torque the screws to 4.5 Nm [3.3 lbf-ft].

Warning

Used magnet carrier screws may loosen and lead to premature failure. Ensure that new screws with

locking compound are utilized.

2. Install the locating dowels (K185) into the dowel holes.
3. Lubricate new O-ring (K175) with petroleum jelly. Install the O-ring to the angle sensor housing

(K265) first.

4. Install angle sensor housing (K265) with O-ring (K175) to housing with 4 screws (K195) and torque to

5.9 Nm [4.4 lbf-ft].

Service Manual

Series 45 E Frame Open Circuit Pumps

Minor repair

38 |

Danfoss | September 2016

AX00000024en-US0401

Содержание Series 45













































Результаты поиска

Содержание Series 45

Отзывы:

Похожие инструкции для Series 45

Бренды по названию

Популярные бренды

Danfoss Series 45, Руководство по обслуживанию

Результаты поиска

Содержание Series 45

Отзывы:

Похожие инструкции для Series 45

Бренды по названию

Популярные бренды