Danfoss Series 40 M46 Tandem Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 48

Danfoss Series 40 M46 Tandem Скачать руководство пользователя страница 32

4. Using a 9/16 in. hex wrench, install screws (1502). Torque to 43 N•m [32 lb•ft].
5. Lubricate and press seal (1504) onto auxiliary pad (1503).

If a gear pump is a ttached to the auxiliary pad, install a new O-ring or gasket and gear pump

6. Install cover plate (1505). Using a 9/16 in. hex wrench, install capscrews (1506). Torque to 30 N•m [22

lbf•ft].

If a gear pump is attached, seal (1504), cover (1505), and bolts (1506) are not used. Replace O-ring or

gasket between gear pump and M46 pump.

Shaft seal, roller bearing and shaft replacement

The shaft assembly is serviceable without removing the front cover of the pump, but the charge pump
must be removed first. Orient the pump on the work surface so the shaft is pointing up with the charge
pump (603) and key (605) removed from shaft. See

Charge pump

on page 30

Removal

1. Using a snap-ring pliers, remove snap-ring (132) from pump cover. Remove and discard seal (301).

Remove second snap-ring (132).

2. Remove shaft assembly from pump cover.

C

Caution

Do not damage the housing bore, shaft, or bearing when removing the shaft and shaft seal.

3. Using a snap ring pliers, remove both snap-rings (133). Press bearing (131) off of shaft.

C

Caution

Do not rotate or move pump after removing shaft. Internal components may be dislodged making

shaft replacement impossible without complete disassembly.

Shaft assembly

P106 637E

401

132

132

133

133

131

301

Service Manual

Series 40 M46 Variable Pumps

Minor repair

32 |

©

Danfoss | September 2017

11026743 | AX00000027en-US0202

«
...
30
31
32
33
34
...
»

Содержание Series 40 M46 Tandem

















































Отзывы:

Нет отзывов