manualshive.com logo in svg

Danfoss pved-cl, Руководство по эксплуатации, Страница: 44 / 116

Поделиться
Скачать
Danfoss pved-cl Скачать руководство пользователя страница 44

Sts3 sets the steering ratio when the vehicle is driving at 25.00% of Vesm.
Sts4 sets the steering ratio when the vehicle is driving at 50.00% of Vesm.
Sts5 sets the steering ratio when the vehicle is driving at 100.00% of Vesm.
Vesm sets the region where steering sensitivity is variable to vehicle speed. The default value is set at the
maximum speed of most applications.

Symbol

Index

Default

Value range

Vcap

706

25

5 to 120 (L/min)

StrkVol

707

600

100 to 8000 (ccm)

Sse

1y09

1

Must be set at 3

Sts0

1y10

400

20 to 1200

Sts1

1y11

400

Sts0 to 1200

Sts2

1y12

400

Sts1 to 1200

Sts3

1y13

400

Sts2 to 1200

Sts4

1y14

400

Sts3 to 1200

Sts5

1y15

400

Sts4 to 1200

Vesm

1y16

500

1 to 1000 (0.0 to 100.0 km/h)

Please note the parameter dependency of Sts. Steering sensitivity of 400 equals to 4.00 steering wheel turns to move the steering actuator from YL to
YR (left to right end-lock position) See chapters 

Mapping a Steering Device

 on page 31 and 

J1939 Diagnostic Interface

 on page 102 to acquire vehicle

speed.

Ramps (Anti-jerk)

Ramps are normally used to minimize jerk forces in machines with articulated steered steering systems. In
these steering systems, the articulating masses can be instantly stopped by closing the valve oil flow. An
instant cylinder movement stop starts the articulating masses to oscillate until all kinetic energy is
dispatched into heat by the shock valves or by the friction between wheels and ground. Jerk is an
inherent characteristic of articulated steered vehicles and cannot be completely removed. However, it is
best minimized when the forces are monotonically reduced in magnitude.

To achieve this, the EHPS software provides linear or non-linear ramps which in effect creates an orifice
across the main spool to tank by holding the valve open near its closing position until all kinetic energy is
dispatched into heat for some time. Ramps work on the valve spool set-point.

Ramps with Fixed Ramp Times

Sr sets the method. The ramp times can be disabled, fixed or related to vehicle speed. Set Sr to:

•

0 to select no ramps (default),

•

1 to select fixed ramp times, or

•

2 for speed dependent ramp times.

Symbol

Index

Default

Value range

Sr

1y17

0

0 (default)

The figure below shows the operation of ramps with fixed ramp times and illustrates different ramp
scenarios. Qr is the request port flow commanded with the steering wheel. Qramp the ramp limited port
flow and can be regarded as the result of the ramp function.

Operation Manual

PVED-CL Controller for Electro-Hydraulic Steering, Version 1.38

Steering by Steering Wheel – Open Loop

 

44 | 

©

 Danfoss | May 2016

11025583 | AQ00000216en-US0302

Содержание pved-cl





















































































































Отзывы:

Нет отзывов