manualshive.com logo in svg

Danfoss EM-PMI540-T4000, Руководство пользователя

Поделиться
Скачать
Danfoss EM-PMI540-T4000 Скачать руководство пользователя страница 47

1. Connect one terminal of the measurement device to the cable shield of one power cable (in the

inverter end of the cable)

2. Connect the other terminal of the measurement device to the cable shield of an other power cable.

You can also use the machine enclosure grounding point for the measurement.

3. Measure the resistance between the two cable shields or between the cable shield and the enclosure

grounding point.

4. Change the measurement device terminal(s) to the shield of different power cable and repeat the

measurement until all cables have been measured.

Testing the low voltage (measurement signal) cable shield grounding (earthing)

The low voltage (measurement signal) cable shield connects to the ground through the connector
grounding/earthing pins. After cable installation, and any time when needed, make sure that the
grounding (earthing) connection is valid.

1. Connect one terminal of the measurement device to the low voltage cable shield (in the non-

machine end of the cable).

2. Connect the other terminal of the measurement device to the machine enclosure grounding point.
3. Measure the resistance between the cable shield and the enclosure grounding point.

Anti-condensation heater connections

Do not run the electric machine when an anti-condensation heater is in use.

Water condensing inside the electric machine enclosure can result in failure or corrosion of the electric
machine. This often happens in cooler temperatures or higher humidity areas typically in marine
environment, when the machine is not running.

The electric machine can be equipped with anti-condensation heater to avoid condensation issues. The
anti-condensation heater (+HEAT1) or heaters (+HEAT2) are factory assembled. The installed heater may
not be used when the electric machine mains are switched on or when the electric machine is running.

The installed anti-condensation heater must be supplied with 230 Vac power. The heater connector used
is HUMMEL Twilock connector, illustrated in Figure below.

User Guide

EM-PMI540-T4000

Installation

 

©

 Danfoss | April 2023

BC265857716810en-000202 | 47

Содержание EM-PMI540-T4000








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды