manualshive.com logo in svg

Danfoss EM-PMI540-T4000, Руководство пользователя

Поделиться
Скачать
Danfoss EM-PMI540-T4000 Скачать руководство пользователя страница 44

Pin configuration of the Deutch HD34-24-47PE connector (continued)

Measurement

Description

PIN

Resolver EXCP

Resolver, EXCP, in-built non contacting

10

Resolver shield

Resolver, SHIELD/GROUND, in-built non contacting

34

Bearing temperature measurement connector

1

PT100 pin

2

PT100 pin

3

PT100 ground pin

4

PT100 ground pin

Grounding connections

Ground the electric machine from its frame to make sure it functions correctly and safely.

Ground the cable shields of the power cables to make sure the electric machine functions

correctly and safely.

Ground the cable shields of the instrumentation cables to make sure the electric machine

functions correctly and safely.

It is recommended to perform a ground bond test after installing the electric machine to make

sure the electric machine is correctly grounded.

User Guide

EM-PMI540-T4000

Installation

 

44 | 

©

 Danfoss | April 2023

BC265857716810en-000202

Содержание EM-PMI540-T4000








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды